MacMusic.org  |  PcMusic.org  |  440Software  |  440Forums.com  |  440Tv  |  Zicos.com  |  AudioLexic.org
Loading... visiteurs connectés
 
Reply to this topicStart new topic
> Reverb Questions, Need help replicating a reverb technique
adachis
posté dim. 23 nov. 2003, 10:39
Message #1


Newbie


Groupe : Members
Messages : 5
Inscrit : 23 nov. 03
Lieu : Boston - US
Membre no 29,493




I'm trying to replicate certain type of reverb but I don't know how. I don't know how to explain it too well either so here's what I'm talking about:

15 sec. sample in MP3 format, 358k

I know it's done with a heavily modified Fat Plate on a Lexicon 480, but I'm wondering if this can be done with software reverb. It sounds like the reverb is only on the really high, breathy part of the vocals. It sounds very ethereal, and I'd like to know how to do that. If anyone knows, please help. I know a little bit, but I'm pretty new to this stuff so don't assume too much. Also, I am running Cubase SX, and I have access to Altiverb and Trueverb in addition to the included Spectral Design Reverb A/Reverb B plug-ins included with Cubase.


Thanks!
Adam
Go to the top of the page
 
+Quote Post
pronkie5
posté ven. 2 janv. 2004, 21:04
Message #2


Newbie


Groupe : Members
Messages : 21
Inscrit : 02 janv. 04
Lieu : Hilversum - NL
Membre no 32,237




pfew...this is a hard one because there are various options;

1) make the reverb a send effect. on send channel put a high-pass filter (eq) set to about 3K.. this way you're left with the high content.
2) duplicate the vocal track (or any track you want to use) and remove lows with EQ. Don't play this track back but send content to: a reverb.

These are the 2 easiest ways. You'll probably get what you want this way.

Jan

PS: I know there are other ways but harder to explain...
Go to the top of the page
 
+Quote Post
adachis
posté ven. 2 janv. 2004, 21:20
Message #3


Newbie


Groupe : Members
Messages : 5
Inscrit : 23 nov. 03
Lieu : Boston - US
Membre no 29,493




I apologize, I don't follow you completely. I think I'm understanding up until you say "send the content to: a reverb". How do I do that (with Cubase)? Is it possible with the plug-ins I'm using or should I be using something else?


Thanks so much for your help!!
Adam
Go to the top of the page
 
+Quote Post
rolle33
posté sam. 3 janv. 2004, 14:34
Message #4


Newbie


Groupe : Members
Messages : 15
Inscrit : 29 déc. 03
Lieu : Karlsruhe - DE
Membre no 32,005




Hi,

with Cubase you must duplicate your track, EQ it and put the send to prefade. this means, your signal goes to the reverb-unit before it goes through the channel-fader. then put the channel fader to 0.
don`t forget to put the Mix of your reverb-unit to "wet-only" (no Original-Signal).

so it works...

but i think the best way for that sound is to have a good 480 impuls response for Altiverb...
duplicate your vocal track and don't (!!) compress this one. set the send to prefade, Channelfader to 0 and go through Altiverb/480 Plate
Compress your Mainvocal 4:1 (or whatever you need) and mix it with the wet Signal of Altiverb. you may need a predelay higher than 30 ms for that sound. just try...
what do you need more? Tori Amos' Voice... rolleyes.gif

have fun

Rolf
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 utilisateur(s) sur ce sujet (1 invité(s) et 0 utilisateur(s) anonyme(s))
0 membre(s) :

 

Version bas débit - jeudi 5 déc. 2024, 04:45
- © 440 Forums 2011